<< December 2017 >>
Sun Mon Tue Wed Thu Fri Sat
 01 02
03 04 05 06 07 08 09
10 11 12 13 14 15 16
17 18 19 20 21 22 23
24 25 26 27 28 29 30

If you want to be updated on this weblog Enter your email here:

rss feed

Mar 2, 2014
Some Information About Heat Exchanger Selection Criteria

1 There are some heat exchanger selection criteria from china solar collector you should know, at first, clean the exterior of the heat exchanger to get rid of any debris on the device.

2 Available the entry panel and visually inspect the heat exchanger making use of a telescoping mirror and an effective flashlight on each the exterior and inside of the heat exchanger. Glimpse for indicators of severe deterioration, open cracks or split seams. If there are any bigger cracks, they are usually identifiable making use of this visual inspection. Steel expands when heated, and the crack might not be completely noticeable although the furnace is turned away.

3 Have some1 turn the furnace on and timepiece the flame for modifications in its conduct. Sit in entrance of the furnace to observe the flame, but retain a risk-free range to stay clear of melts away. The contact for solar water heater china from the thermostat will begin the furnace but not the blower. The flame will be present for a brief period of time prior to the blower turns on. If there is a crack in the heat exchanger, the oxygen from the blower will make the flame look like it is dancing or altering coloring. There must be no change in the flame's conduct when the blower turns on.

4 Perform the methane (CH4) method, suggested by the American Gas Association (AGA). To do this, reduce a 3-inch hole in the plenum, just above the heat exchanger. Allow the furnace to run for 5 minutes. With the heat exchanger nevertheless cozy, inject the tracer gasoline into the bottom of the heat exchanger at a fee of 7 cubic feet every hour. Move a detector probe back again and forth in the 3-inch hole for two minutes. If an unacceptable leak is detected, the probe detector will lighting up or signals the stress of the tracer gasoline. We supply the following products: solar geyser heat collector solar heater

Posted at 09:45 pm by micoe1401
Make a comment  

Feb 7, 2014
How to Build a Simple Passive Solar Water Heater?

Take pleasure in a normally heated shower with a passive solar geyser system. Power conservation is necessary, no matter whether you're worried about your carbon footprint or just want to spend less some bucks on power expenses. Relying on option energy options, such as wind or solar, is a superb way to decrease your dependence on pricey electrical power and fossil fuels. With some effortless materials and a tiny time, you can develop a solar water heater like stainless steel solar geyser that will supply you with a lot of warm water.Here are certain directions:

solar water heater

1 collect materials
Check out thrift shops and development recycling sites to come across the good that you require for this job. If your regional dump has a coolant selection plan that removes Freon from aged refrigerators and oxygen conditioners, it's most likely they'll have a lot of aged refrigerators lying close to, and you can get the heat dispersal system situated on the back again for a reduced price or even absolutely free. Scrap wooden and possibly the oxygen pump hose can also be discovered at the landfill. Other good can be discovered close to the home or at developing provide shop for a reduced price. Assemble all your goods in a garage prior to beginning to make certain you have every little thing you require, and possibly extra good in case an incorrect cut is created or an errant hole is drilled. Collect the good you'll require such as saws, drills, wooden nails, drill bits, security goggles and gloves solar geyser evacuated tube.

2 prepare for construction
Get rid of the heating coil from the back of the applied refrigerator, leaving the two end tubes intact and producing certain you get away from ample leads on the end for attaching the water hoses later on. Cut your backing substance to the relative sizing of the pane of decanter or glass that you're making use of. An aged industrial sizing doormat can be fantastic for this backing, but it may carry you a minute to cut down to sizing. Dim colored felt will also operate perfectly well. Prepare a big item or items of aluminum foil to produce an further reflective layer, the same exact sizing as the backing.

3 make the frame
Construct a set of two wooden frames about the same exact sizing as the backing you've cut down. Assemble the items of wooden into a rectangle, lay the backing and aluminum foil on the frame, and lock them into location by developing a comparable frame on the back. Drive big wooden screws via the entrance frame, the backing and into the back frame to put every little thing in location. Use duct tape or caulk to seal any cracks on the within of the frame. We supply the following products: non-pressure water heater split pressurized solar geyser integrated pressurized solar geyser

Posted at 06:46 pm by micoe1401
Make a comment  

Jan 16, 2014
How to Make a Solar Water Heater from Glass Bottles

Solar energy is a powerful force that people are beginning to consider using for everything from powering cars to heating water. If you’re as arranged has entire sunshine coverage throughout the day time, many heaters can manage all or some of your water heating requirements. Goblet bottles are finest to use for a solar water heater, as the warm water could result in plastic material bottles to livery chemical compounds. Whilst not all plastic material consists of chemical compounds, glass bottles are ordinarily safer. You should know u pipe collector and u pipe solar collector well.

solar water heater

1 U pipe collector and u pipe solar collector. First, you can scrub and dried out the glass bottles totally. Any sizing of glass bottles will operate.

2 Then you can paint the bottles with a spray-on primer in the darkest color you can get, for maximal heat absorbency. Permit the bottles to dry out totally.

3 Drill a hole into the bottom of the bottles, 1 inch in diameter.

4 Then paint the bottles with flat dark spray paint. Permit the bottles to dry out totally.

5 You can thread the hose via the bottles, stacking the bottles neck to end. Use epoxy to maintain the bottles jointly. Make columns of bottles with 4 to 6 bottles in every column. Reduce the hose about 2 inches beneath the bottom bottle and about 2 inches above the top bottle.

6 You should know that paint the plywood dark and allow it to dry out. You can Location the initial column of bottles on the plywood. Hammer nails into possibly facet of the neck to retain the initial bottle in place. Repeat this for every bottle in the column. You can Location the following column of bottles be facet the initial and repeat.

7 Paint the PVC and t-joints dark and arranged a facet to dried out.

8 Insert a t-joint into every of the cut ends of the hose that key and exits the bottles.

9 The nest step, you can calculate and cut the PVC pipe to connect the t-joints. Utilize glue to the joints and allow it to dry out.

10 Operate PVC pipe to the storage space tank that will maintain the water. Water will go up as it heats, developing a thermo siphon to gradually draw water up. Hot water exiting the top of the columns of bottles really should key in the top of the tank, and colder water that goes to the bottom of the columns of bottles really should exit the bottom of the tank. Repeat this procedure as normally as you desire to make sufficient warm water for your requirements. We supply the following products: solar geyser manufacturer solar geyser systems solar energy water heater

Posted at 01:23 am by micoe1401
Make a comment  

Jan 14, 2014
Some Types of Heat Exchangers You Should Know

There are certain types of heat exchanger like plate solar water heater heat exchanger or pressurized solar geyser for you:

Heat exchangers are mechanized equipment utilized to move heat from a single fluid to an additional over a rock solid surface area. They are developed to be effective and the movement of heat happens possibly via absorption of heat by a single fluid from an additional or via dissipation. Heat exchangers are discovered in an assortment of gear which includes refrigerators, air conditioning devices, furnaces and boilers. In most heat exchangers, fluids are divided by a heat transfer surface area that does not enable them to combine. This is referred as a direct transfer sort, or recuperators. Heat exchangers that enable for intermittent transfer among fluids are referred to as indirect transfer sorts or storage space sorts.

solar water heater

Shell and tube
Shell and tube heat exchangers are created with circular tubes connected to cylindrical shells with their axes coaxial with the shell axis. In accordance to heat exchangers by Dr. Osama, the particular variations among these sorts of exchangers are discovered in the design characteristics. These sorts are discovered in petroleum-refining and substance companies as well as in waste materials heat recovery applications.

Double pipe and compact
Double pipe heat exchangers consist of a single pipe positioned within an additional one with a bigger diameter. The sections are attached in a sequence or parallel plans, depending on requirement. These sorts of equipment are little and are utilized for little quantities of heat transfer (up to 50 m), according to Dr. Abdel. Compact heat exchangers are classified according to the type of compact components discovered inside of them. There are 5 completely different sorts, which include round and flattened round tubes, tubular surface areas, surface areas with flow typical, plate fin surface areas and finned tube surface areas. All 5 sorts have a single fundamental aspect, which is the major (a double of parallel plates with connections of metal).

Plate and frame
Plate and frame heat exchangers are constructed on slim plates that do not accommodate quite substantial pressures and temperatures. They are light and little and are generally utilized in weight-delicate places such as ships and oil manufacturing platforms. Plate and frame heat exchangers may perhaps also be classified as plate, spiral plate, lamella and plate coil exchangers, according to dr. Abdel.

Spiral and regenerative
Spiral exchangers consist of two lengthy, parallel plates which are arranged into a spiral. The open sides are sealed away and kept in location by clamps. The top and bottom addresses are removable, hence enabling the spiral exchanger to be quickly cleaned. Regenerative exchangers shop heat and eliminate it from a surface area. These sorts of exchangers are developed with a matrix that can proceed quickly in to and out of repaired warm and chilly fluid streams. Regrettably, regenerators are recognized to endure from leakage and fluid issues, according to dr. Abdel. However, they are utilized extensively in electric energy producing stations for preheating of air.

Scrapped surface
Scrapped surface area exchangers are utilized in circumstances exactly where the fluid is in all probability to crystallize on cooling. They have a broad variety of apps which include meals, substance, pharmaceutical and petrochemical companies.

We supply the following products: non-pressure water heater integrated pressurized solar geyser pressurized heat pipe solar water heater

Posted at 11:28 pm by micoe1401
Make a comment